200-105 Which connection uses the default encapsulation for serial interfaces on Cisco routers? A. The serial connection to the NorthCoast branch office. B. The serial connection to the North branch office. C. The serial connection to the Southlands branch office. D. The serial connection to the Multinational Core. Correct Answer: B Explanation Explanation/Reference: Cisco default encapsulation is HDLC which is by default enabled on all cisco router. If we want to enable other encapsulation protocol (PPP,X.25 etc) we need to define in interface setting. But here except s1/1 all interface defined by other encapsulation protocol so we will assume default encapsulation running on s1/1 interface and s1/1 interface connected with North QUESTION 7 Which statement about access lists that are applied to an interface is true? A. You can place as many access lists as you want on any interface. B. You can apply only one access list on any interface. C. You can configure one access list, per direction, per Layer 3 protocol. D. You can apply multiple access lists with the same protocol or in different directions. Correct Answer: C Explanation QUESTION 8 After the network has converged, what type of messaging, if any, occurs between R3 and R4? A. No messages are exchanged. B. Hellos are sent every 10 seconds. C. The full database from each router is sent every 30 seconds. D. The routing table from each router is sent every 60 seconds. Correct Answer: B Explanation Explanation/Reference: HELLO messages are used to maintain adjacent neighbors so even when the network is converged, hellos are still exchanged. On broadcast and point-to-point links, the default is 10 seconds, on NBMA the default is 30 seconds. QUESTION 9 To allow or prevent load balancing to network 172.16.3.0/24, which of the following commands could be used in R2? (Choose two.) A. coque iphone 8 R2(config-if)#clock rate B. coque iphone pas cher R2(config-if)#bandwidth C. R2(config-if)#ip ospf cost D. R2(config-if)#ip ospf priority E. R2(config-router)#distance ospf Correct Answer: BC Explanation Explanation/Reference: OSPF Cost http://www.cisco.com/en/US/tech/tk365/technologies_white_paper09186a0080094e9e.sht ml#t6 The cost (also called metric) of an interface in OSPF is an indication of the overhead required to send packets across a certain interface. The cost of an interface is inversely proportional to the bandwidth of that interface. coque iphone A higher bandwidth indicates a lower cost. coque iphone 7 There is more overhead (higher cost) and time delays involved in crossing a 56k serial line than crossing a 10M ethernet line. The formula used to calculate the cost is: cost= 10000 0000/bandwith in bps For example, it will cost 10 EXP8/10 EXP7 = 10 to cross a 10M Ethernet line and will cost 10 EXP8/1544000 =64 to cross a T1 line. By default, the cost of an interface is calculated based on the bandwidth; you can force the cost of an interface with the ip ospf cost interface subconfiguration mode command. coque iphone en ligne QUESTION 10 What would be the destination Layer 2 address in the frame header for a frame that is being forwarded by Dubai to the host address of 172.30.4.4? A. 825 B. 230 C. 694 D. 387 Correct Answer: C https://www.gk4exam.com/exam/300-550.html Explanation Explanation/Reference: According to command output 172.30.4.4 is using the 694 dlci value. http://www.cisco.com/en/US/docs/ios/12_2/wan/command/reference/wrffr4.html#wp102934 QUESTION 11 Scenario Refer to the topology. Your company has connected the routers R1. coque iphone x R2. coque iphone and R3 with serial links. R2 and R3 are connected to the switches SW1 and SW2, respectively. SW1 and SW2 are also connected to the routers R4 and R5. The EIGRP routing protocol is configured. You are required to troubleshoot and resolve the EIGRP issues between the various routers. Use the appropriate show commands to troubleshoot the issues. A. The K values mismatch. B. The AS does not match. C. The network command is missing. D. The passive-interface command is enabled.
You are here: / / Vendor: Cisco Exam Code: 200-105 Exam Name: Interconnecting Cisco Networking Devices Part 2